Leading 10 typical forklift crashes ， forklift operation should take note of these matters ！.

Leading 10 typical forklift crashes ， forklift operation should take note of these matters ！.

Blog Article

Do not undervalue the forklift at work. If the operation is not good, there will certainly be significant crashes in minutes, and there are many accidents involving forklifts.

Situation 1: The forklift cargo blocked the motorist's sight, and the person in front might not be found, resulting in a rolling accident.
Case 2: In order to maintain the equilibrium of the forklift when raising hefty products, the workers used their body weight as the counterweight, which practically caused casualties.
Case 3: The size of the forklift freight surpasses the permitted width of the route and holds on the roadside rack, which nearly triggers an accident.
Case 4: Forklift is speeding up and surrender during a turn.
Case 5: The forklift driver did not observe the pedestrian, and the pedestrian did not observe the forklift.
Situation 6: The forklift lifts the employees unlawfully, the forklift chauffeur does not wear the safety belt, the forklift lifter drops and the chauffeur is squashed when the forklift surrender.
Case 7: The forklift driver did not put on a seat belt and dropped from the automobile when it rolled over and was squashed.
Forklift procedure ought to pay attention to these issues ：.

Begin.
1. Before beginning, observe the surroundings, and after validating that there are no challenges that hinder the security of driving, honk the horn initially and then begin.
2. For cars with hydraulic ( atmospheric pressure) brakes, the brake hydraulic pressure ( atmospheric pressure) gauge must be risk-free before beginning.
3. When the forklift begins with a tons, the driver must first verify that the lots is stable and reliable.
4. The begin must be sluggish and steady.

Driving.
1. When driving, the height in between the bottom end of the fork and the ground should be maintained 300mm-400mm, and the pole must be tilted backwards. .
2. Do not raise the fork too high when driving. When going into and leaving the work site or while driving, beware that there will certainly be no obstacles overhead. When the lots is traveling, the fork needs to not be elevated too high, which will influence the security of the forklift. .
3. After unloading, the fork must be decreased to the normal driving position before driving. .
4. When transforming, if there are pedestrians or lorries nearby, the driving signal should be provided initially. High-speed doglegs are restricted. High-speed sharp turns will certainly create the vehicle to lose lateral security and topple. .
5. When the forklift is downhill, it is purely forbidden to turn off the flame and slide, and it is prohibited to brake instantly while driving with lots unless there are special situations.
6. When the forklift is running, it needs to comply with the website traffic rules in the factory and must keep a certain security distance from the automobile in front. .
7. When the forklift is running, the load should be in the lowest setting that does not impede the driving, and the gantry must be appropriately slanted back. The tons shall not be increased except when stacking or loading. .
8. The height of the lots have to not obstruct the vehicle driver's sight. In unique conditions, when the thing influences the forward vision, drive at a reduced speed when reversing.
9. It is forbidden to turn on the ramp, neither to drive throughout the ramp. .
10. The risk-free driving speed of the forklift in the factory location is 5 km/h, and it needs to drive securely at a low speed when getting in the manufacturing workshop area. .
11. When the forklift is lifted, raised or driven, it is prohibited for workers to stand on the fork to hold things and play a stabilizing function. .
12. If problems are located, they will certainly be repaired and reported in a timely fashion, and they will certainly never run with health problems or hide them.

packing and discharging.
1. When fork-loading items, the range in between the two forks should be adjusted as required to make the lots of both forks balanced and not manipulated, and one side of the product should be against the rack. .
2. It is restricted to work with a solitary fork or utilize a fork top or draw. In special situations, security warning signs should be established to remind bordering pedestrians. .
3. In the process of loading and dumping items, the forklift has to be stopped with the brake. .
4. The speed of the vehicle need to be sluggish and consistent. Be careful not to roll the wheels on the dunnage, so as not to extend the rolled objects and harm people. .
5. When making use of a fork to fork the goods, the fork must be as deep as possible under the tons, and it needs to be noted that the fork suggestion must not touch various other items or objects. The load ought to be maintained with minimal back tilt of the gantry to ensure that the tons does not move in reverse. The mast can be slanted onward slightly when the tons is decreased to enable simple positioning of the lots and extraction of the forks. .
6. It is restricted to fork goods at high speed and hit hard objects with the fork head. .
7. When the forklift is working, it is restricted for individuals to stand around the fork, so as to prevent the collapse of the goods and injure people. .
8. Overwhelming is banned, and it is prohibited to make use of forks to raise employees to participate in high-altitude procedures to avoid high-altitude falling mishaps. .
9. It is not allowed to make use of the brake inertia to slip, place, round or roll things. .
10. It is not permitted to make use of forks to pick, turn pallet discharge.

Leaving .
1. It is forbidden to leave the forklift when the items on the fork are in the air. Before leaving the forklift, you should discharge the goods or reduced the fork framework.
2. Draw the emergency brake manage to dead or dispirit the hand brake button.
3. The engine is switched off and the power is removed. (Except for special situations, such as the driver does not leave the vehicle's line of sight and does not exceed 1 minute).
4. Get rid of the trick. .

Forklift Operation Precautions.
1. Prior to and after the forklift procedure, the look ought to be inspected, and fuel, lubricating oil and air conditioning water need to be included.
2. Inspect the security performance of beginning, running and stopping.
3. Inspect Stand-on Electric Pallet Stacker whether the lights and horn signals are total and effective.
4. During the procedure of the forklift, inspect whether the pressure and temperature are regular.
5. After the forklift is running, the exterior leak ought to also be examined and the seals should be changed in time.

Forklift Safety Operation Specifications.
1. You have to check prior to leaving the cars and truck;.
2. When you come across somebody before you during driving, you must send a signal at a distance of 5 m;.
3. The driving speed in the manufacturing facility does not surpass 5 km/h;.
4. When driving, the low point of the cargo need to be 0.3 m ~ 0.4 m above the ground;.
5. The transforming ought to not be too sharp to stop the tendency of "free turning";.
6. Adding and down the slope must be sluggish and uniform, and no switching on the incline is permitted.
7. Do not drive across the slope. When the slope is greater than 10%, the vehicle needs to be driven backwards when worsening;.
8. When the forklift employees carry the goods and progress, if they experience huge or hefty items and most likely to the motorist's line of vision, they ought to take the reversing workout
.
The "Eight Prohibitions" should be followed in the procedure.
1. Single fork procedure is not allowed.
2. It is not enabled to lift the goods for far away driving.
3. It is not enabled to get the goods by turning over the pallet with the fork.
4. It is not permitted to straight shovel chemicals, flammables and various other harmful chemicals with forks.
5. It is not allowed to make use of inertia pressure to get the goods.
6. It is not allowed to utilize stopping force to exile round or easy-to-roll items.
7. It is not permitted to bring people to deal with the Stand-on Electric Pallet Stacker pallet or fork, and it is purely restricted to stand under the fork after the fork is elevated.
8. Do not drive laterally on slopes
.
Car park is not permitted under the following problems.
1. Curves, slim roadways, train crossings;.
2. Sections with a longitudinal slope higher than 5%.
3. When there is an challenge on one side of the roadway, the contrary side of the area with the same length as the challenge should be within 20 meters at each end.

Web：https://www.onenforklifts.com/
Email：info2@onen.cn
Phone：+86 13827083844